Build an Outdoor Bar
Build an Outdoor Bar
Whether looking for a pub which has a small footprint for casual entertaining on the deck, a classy wine channel or a sturdy potting bench, 1 piece of furniture could fit all of your needs. This patio bar isn't hard to build, but the beauty and endurance of exotic hardwood makes it the ideal bar for both function and fashion.
You Will Need Eight 1-inch x 6-inch x 8-foot Ipe or alternative hardwood / two 50-piece boxes 1 1/2-inch stainless steel screws / 10-inch x 22-inch under-cabinet wire wine rack (optional) / teak oil / belt or orbital sander / tape measure / circular or miter saw / drill with 1/8-inch countersink bit and screwdriver tip / wood clamps / cloth rag
Sand Planks Using a orbital or buckle sander, sand boards to remove blemishes from the surface.
Measure and Mark Pieces With a tape measure and pencil, measure the subsequent lengths to be cut from the ipe boards: Three 42-inch, six 41-inch, one 39-1/2-inch, six 38-inch, six 13-inch.
Cut Measured Lengths Use a round or miter saw to cut pieces to quantified lengths for meeting. Ipe (pronounced "ee-pay") is a very dense hardwood similar to teak and also a sharp blade is recommended. In case Ipe is unavailable locally, other exotic hardwoods like Brazilian redwood, teak or mahogany may supply the mix of durability and beauty ipe offers.
Assemble Top Support Utilizing wood clamps, assemble a box using 2 41-inch and 2 13-inch lengths of timber together with the ends of the sides exposed. This part will encourage the bar top and supply a solid anchor for the legs.
Drill Pilot Holes for Screws With a sharp 1/8-inch bit using a countersink, drill thee pilot holes spaced equally at every corner 3/8-inch from the border. Countersink allows screw heads to rest flush with the surface of the timber.
Add Screws to Top Service Secure support using stainless steel screws driven into pilot holes. Using stainless steel screws are not only strong, but they won't discolor or rust from the components wikipedia reference. Once screws are secure, wood clamps might be removed.
Place Bar Top Lay three 42-inch lengths of timber in addition to the support with a 1/2-inch overhang on each end and 1 inch over the long borders.
Attach Bar Top Ensure that top is resting evenly on service with all edges flush and square click here for more info. Drill two pilot holes into each plank spaced 7/8-inch out of end and 1-1/2 inches from long sides and then attach shirt to support screws.
Assemble Bottom Support Use two 38-inch bits and two 13-inch bits to create a box. Much like the top support, hold the box you created in place with wood clamps, drill three pilot holes spaced equally at each corner 3/8-inch in the edge and finish assembly with stainless steel screws driven into each pilot hole.
Attach Bottom Shelf into Bottom Support Eliminate wood clamps and place three 38-inch boards on top of bottom support, flush on each end and with an overhang of 1 inch along each long side. Drill two pilot holes into every plank spaced 3/8 inch from end and 1-1/2 inches from long sides and then attach bottom plate to support with screws.
Attach Legs Clamp four 41-inch boards into the interior of each corner of the highest support, together with the face against the short side hop over to this website click here for info. On each leg, then drill four pilot holes spaced 1-1/2 inches from the edges of the sides to where it will be attached. Be careful to set the thickness of your drill bit to 1-1/2 inches to prevent drilling through the face of the service Discover More Here. Secure with screws and remove wood clamps.
Attach Bottom Support Turn the pub over to rest on its legs and lay two pieces of scrap 2-inch x 4-inch timber beneath. Rush the bottom support on the scrap lumber, based with a 1/2-inch over stride in the front and rear their explanation. On each leg, drill four pilot holes spaced 1-1/2 inches from the edges of the faces of this service. By driving screws secure.
Attach Side Brace Measure 23 inches upward from the very top of the bottom shelf on each side and also use timber clamps to attach a 13-inch plank with the top border at the 23-inch mark . Make sure braces are level and drill a pilot hole at each corner of this brace 1-1/2 inches from the top and bottom of the brace. Affix with screws and eliminate straps.
Attach Back of Middle Shelf Utilize wood clamps to attach a 39-1/2-inch plank to the rear of the bar with the base edge level with the top of the side braces. At each end, drill a pilot hole on top and bottom on the board 3/8 inches in the end and 1-1/2 inches in the long border look at this now. Drive screws to each of the four pilot holes to fasten and remove clamps.
Attach Middle Shelf Lay a 38-inch plank onto the side straps firmly against the rear of the shelf. Drill four pilot holes, one in each corner of the plate 3/8 inches in the end and 1-1/2 inches from the long sides click this over here now. Drive screws to secure shelf.
Attach the Wine Rack A cable under-cabinet wine rack could be connected to the underside of the bar for easy wine glass storage. A 10-inch x 22-inch rack will hold up to 18 glasses. Attach per maker directions, but be sure to drill pilot holes to get almost any screws required.
Apply Teak Oil After teak oil is employed using a cloth rag, the beauty of hardwood becomes quickly apparent. Since teak oil brings out the natural color of the timber, it enahnces the visual appeal while protecting the timber from mould and sun damage.
Let Dry and Place Allow the teak oil to absorb into the wood and dry completely, anywhere from two to four hours. After dry, your bar is complete and ready to be used.
Sturdy and Versatile This easy-to-build pub is sturdy enough to use as a potting bench, however its beauty makes it the ideal bar, hors d ouerve dining or table space for your deck, patio, kitchen or living room.
You Will Need Eight 1-inch x 6-inch x 8-foot Ipe or alternative hardwood / two 50-piece boxes 1 1/2-inch stainless steel screws / 10-inch x 22-inch under-cabinet wire wine rack (optional) / teak oil / belt or orbital sander / tape measure / circular or miter saw / drill with 1/8-inch countersink bit and screwdriver tip / wood clamps / cloth rag
Sand Planks Using a orbital or buckle sander, sand boards to remove blemishes from the surface.
Measure and Mark Pieces With a tape measure and pencil, measure the subsequent lengths to be cut from the ipe boards: Three 42-inch, six 41-inch, one 39-1/2-inch, six 38-inch, six 13-inch.
Cut Measured Lengths Use a round or miter saw to cut pieces to quantified lengths for meeting. Ipe (pronounced "ee-pay") is a very dense hardwood similar to teak and also a sharp blade is recommended. In case Ipe is unavailable locally, other exotic hardwoods like Brazilian redwood, teak or mahogany may supply the mix of durability and beauty ipe offers.
Assemble Top Support Utilizing wood clamps, assemble a box using 2 41-inch and 2 13-inch lengths of timber together with the ends of the sides exposed. This part will encourage the bar top and supply a solid anchor for the legs.
Drill Pilot Holes for Screws With a sharp 1/8-inch bit using a countersink, drill thee pilot holes spaced equally at every corner 3/8-inch from the border. Countersink allows screw heads to rest flush with the surface of the timber.
Add Screws to Top Service Secure support using stainless steel screws driven into pilot holes. Using stainless steel screws are not only strong, but they won't discolor or rust from the components wikipedia reference. Once screws are secure, wood clamps might be removed.
Place Bar Top Lay three 42-inch lengths of timber in addition to the support with a 1/2-inch overhang on each end and 1 inch over the long borders.
Attach Bar Top Ensure that top is resting evenly on service with all edges flush and square click here for more info. Drill two pilot holes into each plank spaced 7/8-inch out of end and 1-1/2 inches from long sides and then attach shirt to support screws.
Assemble Bottom Support Use two 38-inch bits and two 13-inch bits to create a box. Much like the top support, hold the box you created in place with wood clamps, drill three pilot holes spaced equally at each corner 3/8-inch in the edge and finish assembly with stainless steel screws driven into each pilot hole.
Attach Bottom Shelf into Bottom Support Eliminate wood clamps and place three 38-inch boards on top of bottom support, flush on each end and with an overhang of 1 inch along each long side. Drill two pilot holes into every plank spaced 3/8 inch from end and 1-1/2 inches from long sides and then attach bottom plate to support with screws.
Attach Legs Clamp four 41-inch boards into the interior of each corner of the highest support, together with the face against the short side hop over to this website click here for info. On each leg, then drill four pilot holes spaced 1-1/2 inches from the edges of the sides to where it will be attached. Be careful to set the thickness of your drill bit to 1-1/2 inches to prevent drilling through the face of the service Discover More Here. Secure with screws and remove wood clamps.
Attach Bottom Support Turn the pub over to rest on its legs and lay two pieces of scrap 2-inch x 4-inch timber beneath. Rush the bottom support on the scrap lumber, based with a 1/2-inch over stride in the front and rear their explanation. On each leg, drill four pilot holes spaced 1-1/2 inches from the edges of the faces of this service. By driving screws secure.
Attach Side Brace Measure 23 inches upward from the very top of the bottom shelf on each side and also use timber clamps to attach a 13-inch plank with the top border at the 23-inch mark . Make sure braces are level and drill a pilot hole at each corner of this brace 1-1/2 inches from the top and bottom of the brace. Affix with screws and eliminate straps.
Attach Back of Middle Shelf Utilize wood clamps to attach a 39-1/2-inch plank to the rear of the bar with the base edge level with the top of the side braces. At each end, drill a pilot hole on top and bottom on the board 3/8 inches in the end and 1-1/2 inches in the long border look at this now. Drive screws to each of the four pilot holes to fasten and remove clamps.
Attach Middle Shelf Lay a 38-inch plank onto the side straps firmly against the rear of the shelf. Drill four pilot holes, one in each corner of the plate 3/8 inches in the end and 1-1/2 inches from the long sides click this over here now. Drive screws to secure shelf.
Attach the Wine Rack A cable under-cabinet wine rack could be connected to the underside of the bar for easy wine glass storage. A 10-inch x 22-inch rack will hold up to 18 glasses. Attach per maker directions, but be sure to drill pilot holes to get almost any screws required.
Apply Teak Oil After teak oil is employed using a cloth rag, the beauty of hardwood becomes quickly apparent. Since teak oil brings out the natural color of the timber, it enahnces the visual appeal while protecting the timber from mould and sun damage.
Let Dry and Place Allow the teak oil to absorb into the wood and dry completely, anywhere from two to four hours. After dry, your bar is complete and ready to be used.
Sturdy and Versatile This easy-to-build pub is sturdy enough to use as a potting bench, however its beauty makes it the ideal bar, hors d ouerve dining or table space for your deck, patio, kitchen or living room.
Comments
Post a Comment